If you wish to install Windows 10 64bit on a HP EliteBook 8570p Notebook-PC you need the following drivers:
Warnung: Some of the drivers below aren´t officially tested by HP with the 8570p. However they work on my device without issues.
The driver below might also apply to HP ProBook 6570b.
Intel Management Engine (ME)
HP HS2350 Mobile Broadband Module (Ericsson F5321gw):
R8V03 (December 05, 2012) - sp60091.exe
R3F02, R1C04, R1C08, R1G04, R3C18 / R3C11 (?) - ?
Note: To check the current WWAN firmware version you can perform the following steps:
1.) Click Start then on Control Panel
2.) Click Device Manager
3.) Expand the Modems category. Right-click H5321gw Mobile Broadband Modem and then click Properties
4.) When the Properties window opens, go to the Diagnostics tab
5.) On Diagnostics tab, click Query modem
6.) After the query, the firmware version is shown on the ATI1 command line on the Diagnostics tab.
Validity Fingerprint Sensor
Note: Some 8570p models do not have this sensor!
Intel HD Graphics 4000 [Device PCI\VEN_8086&DEV_0166&SUBSYS_17DF103C&REV_09]
4229 (5. Aug. 2015) - SP72380.exe [Advised as latest offical version for this device according to the HP Support assistant]
Note: further updates might be able to be downloaded here.
Human Interface Devices:
HP Wireless Button Driver [ACPI\VEN_HPQ&DEV_6001]
IDE ATA/ATAPI Controller
Intel 7 Series Chipset Family SATA AHCI Controller [Device PCI\VEN_8086&DEV_1E03&SUBSYS_17A7103C&REV_04]
HP HD Webcam [USB\VID_04F2&PID_B270&REV_5750&MI_00]
Intel 82579LM [PCI\VEN_8086&DEV_1502&SUBSYS_17A7103C&REV_04]
22.214.171.124 (12/06/2018) - Microsoft (Win10 buildin)
Note: There is no Win10 Intel driver, use the one from the OS!
Intel Centrino Ultimate-N 6300 AGN [PCI\VEN_8086&DEV_422B&SUBSYS_11018086&REV_3E]
Note: The device has 3x3 antennas (see here which speed you can get)
HP HS2350 Mobile Broadband Module (Ericsson F5321gw) [USB\Vid_03f0&Pid_3d1d&Cdc_0d&Mi_06]
126.96.36.199 (June 12, 2012) - sp57664.exe [Advised as latest offical version for this device according to the HP Support assistant]
Note1: Device can be fully disabled in the BIOS
Note2: If successfully you will see "Sensors: HP hs32350 HSPA+ Mobile Broadband Module Geolocation Sensor", "USB: HP hs2350 HSPA+ Mobile Broadband Module USB Device", "Network: HP hs2350 HSPA+ Mobile Broadband Network Adapter" as devices in the Device Manager
Modem (LSI High-Definition Audio (HDA) Modem):
Agere Modem [HDAUDIO\FUNC_02&VEN_11C1&DEV_1040&SUBSYS_103C3066&REV_1002]
188.8.131.52 () - sp57141.exe [Latest Windows 7 Driver!]
Memory technologies controller:
JMicron PCIe SD Host Controller [Device PCI\VEN_197B&DEV_2392&SUBSYS_17A7103C&REV_30]
Broadcom bluetooth (BCM20702A0)
Note: Can be fully disabled in the bios!
Intel ME [PCI\VEN_8086&DEV_1E3A&SUBSYS_17A7103C&REV_04]
HP Mobile Data Protection Sensor [ACPI\VEN_HPQ&DEV_6000]
Note: Uninstall at first ANY old version. Then install it (extract it), once done go into the system settings and manually update the driver here (select the accelerometer.inf in the expanded folder) otherwise an exclamation mark error will appear!
HP Hotkey Support
The HP EliteBook 8570p supports UEFI. To change from the Bios (Legacy) to UEFI perform the following steps:
1.) Change your Windows 10 OS as explained here
2.) At the HP startup screen, hit "ESC" for the "Startup Menu", "F10" for "BIOS Setup"
3.) in "System Configuration" tab, "Boot Options", change "Boot Mode" from "Legacy" to "UEFI Hybrid (With CSM)" for Windows 7 64 bit or even better to "Native UEFI (without CSM)" which is used for Windows 8 64 bit and higher.
How to enter the Bios:
Reset Bios Password:
You can reset the BIOS Password with using a SMC.BIN file you you can only get from the HP support (and not from me)! Its generated by HP using your unique UUID. Once you have the file you need to put that on a 2GB FAT32 formatted USB stick. Put that into your USB2 port, press the windows key and arrow up and arrow down at the same time and start the notebook. Once you see the HP logo you need to press F10. After some moment you will get a "SMC Command Status – SMC command handled successfully." and then can choose "Reset BIOS Security settings". After that you need to save the change via F10.
It you have something to update to the list, feel free to leave a comment