If you wish to install Windows 10 64bit on a HP EliteBook 2570p Notebook-PC you need the following drivers:
Warnung: Some of the drivers below aren´t officially tested by HP with the 2570p. However they work on my device without issues.
Used OS: Microsoft Windows 10´s November 2019 Update, codenamed 19H2, released on November 12. Also known as Windows 10 version 1909
HP HS2350 Mobile Broadband Module (Ericsson F5321gw):
R8V03 (December 05, 2012) - sp60091.exe
R3F02, R1C04, R1C08, R1G04, R3C18 / R3C11 (?) - ?
Note: To check the current WWAN firmware version you can perform the following steps:
1.) Click Start then on Control Panel
2.) Click Device Manager
3.) Expand the Modems category. Right-click H5321gw Mobile Broadband Modem and then click Properties
4.) When the Properties window opens, go to the Diagnostics tab
5.) On Diagnostics tab, click Query modem
6.) After the query, the firmware version is shown on the ATI1 command line on the Diagnostics tab.
Intel HD Graphics 4000 [Device PCI\VEN_8086&DEV_0166&SUBSYS_17DF103C&REV_09]
Known to be not working: 10.18.19.5069 / 188.8.131.5269 (5/15/2019) - win64_184.108.40.20669.exe
IDE ATA/ATAPI Controller
Intel 7 Series Chipset Family SATA AHCI Controller [Device PCI\VEN_8086&DEV_1E03&SUBSYS_17DF10C&REV_09]
Intel 82579LM [PCI\VEN_8086&DEV_1502&SUBSYS_17A7103C&REV_04]
220.127.116.11 (12/06/2018) - Microsoft (Win10 buildin)
Note: There is no Win10 Intel driver, use the one from the OS!
Intel Centrino Advanced-N 6205
15.15.02 (06/01/2015) - Microsoft (Win10 buildin)
HP HS2350 Mobile Broadband Module (Ericsson F5321gw) [USB\Vid_03f0&Pid_3d1d&Cdc_0d&Mi_06]
Note1: Device can be fully disabled in the BIOS
Note2: If successfully you will see "Sensors: HP hs32350 HSPA+ Mobile Broadband Module Geolocation Sensor", "USB: HP hs2350 HSPA+ Mobile Broadband Module USB Device", "Network: HP hs2350 HSPA+ Mobile Broadband Network Adapter" as devices in the Device Manager
Memory technologies controller:
JMicron PCIe SD Host Controller [Device PCI\VEN_197B&DEV_2392&SUBSYS_17DF103C&REV_30]
Broadcom bluetooth (BCM20702A0)
HP 3D DriveGuard (HP ProtectSmart Hard Drive Protection) [Device ACPI\VEN_HPQ&DEV_6000]
Note: Uninstall at first ANY old version. Then install it (extract it), once done go into the system settings and manually update the driver here (select the accelerometer.inf in the expanded folder) otherwise an exclamation mark error will appear!
Intel QM77 Express Chipset LPC Controller
xxxxx (xxxxxx) - Microsoft (Win10 buildin)
Intel Management Engine Interface [Device PCI\VEN_8086&DEV_1E3A&SUBSYS_17DF103C&REV_04]
The HP EliteBook 8570p supports UEFI. To change from the Bios (Legacy) to UEFI perform the following steps:
1.) Change your Windows 10 OS as explained here
2.) At the HP startup screen, hit "ESC" for the "Startup Menu", "F10" for "BIOS Setup"
3.) in "System Configuration" tab, "Boot Options", change "Boot Mode" from "Legacy" to "UEFI Hybrid (With CSM)" for Windows 7 64 bit or even better to "Native UEFI (without CSM)" which is used for Windows 8 64 bit and higher.
How to enter the Bios:
Reset Bios Password:
You can reset the BIOS Password with using a SMC.BIN file you you can only get from HP support (and not from me)! Its generated by HP using your unique UUID. Once you have the file you need to put that on a 2GB FAT32 formatted USB stick. Put that into your USB2 port, press the windows key and arrow up and arrow down at the same time and start the notebook. Once you see the HP logo you need to press F10. After some moment you will get a "SMC Command Status – SMC command handled successfully." and then can choose "Reset BIOS Security settings". After that you need to save the change via F10.
You can upgrade the RAM from the device to max. 16 GB RAM. To perform that you require:
2x 8GB DDR3-12800 (1600-MHz) dual channel 204 pin SO-Dimm
Can the Intel ME firmware 18.104.22.16810 from the HP EliteDesk 800 G2-Tower PC be installed?
It you have something to update to the list, feel free to leave a comment